Epoxy Quick 100

Product specifications

Component A

Density (20°C)1.16 g/cm³

Viscosity (25 °C)950 mPa s

Component B

Density (20°C)0.97 g/cm³

Viscosity (25 °C)800 mPa s

Mixture

Density (20°C)1.08 g/cm³

Viscosity (25 °C)800 mPa s

Once fully cured

Flexural tensile strengthapprox. 20 N/mm² *

Compressive strengthapprox. 65 N/mm² *

* Epoxy resin mortar 1:10 with standard sand

The stated values represent typical product characteristics and are not to be construed as binding product specifications.

‍

Preparation

Substrate requirements

• The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.
• The tensile strength of the surface of the substrate must be at least 1.5 N/mm² on average (smallest individual value of at least 1.0 N/mm²), and the compressive strength must be at least 25 N/mm².
• Substrates must have reached their moisture balance and must also be protected against moisture penetration from the reverse side, including during use.
• Concretemax. 4 m% moisture
• Cement screedmax. 4 m% moisture
• Anhydrite screedmax. 0.3 m% moisture
• Magnesite screed2-4 m% moisture
• In the case of anhydrite and magnesite screeds, moisture cannot be permitted to penetrate from building elements or the ground.
• As a general principle, systems which permit the diffusion of water vapour are recommended for use with anhydrite and magnesite screeds.

Preparations

• Prepare the substrate by suitable means, e.g. steel ball jetting or diamond grinding, so that it meets the requirements specified above.
• Broken out or missing areas in the substrate should be filled flush with the surface using Remmers PCC systems or Remmers EP mortars.

Combination container

• Add the entire quantity of the hardener (component B) to the base compound (component A).
• Mix thoroughly with a slow-speed electric mixer
  (approx. 300 - 400 rpm).
• Pour the mixture into a separate container and mix again thoroughly.
• Mix for at least 3 minutes.
• Insufficient mixing is indicated by streaks forming.

Application

Application requirements

• Temperature of the material, air and substrate: from min. +3 °C to max. +25 °C
• As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

Working tools / cleaning

• Smoothing trowel, toothed trowel, notched spreader, rubber scraper, epoxy roller, spiked roller, mixer, positive mixer if necessary
• More detailed information can be found in the Remmers Tool Programme.
• Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.
• Take suitable protective and waste disposal measures when cleaning.

Storage / shelf life

• If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

Usage

• See application examples

Application examples

Primer

• Apply the mixed resin generously to the surface. Distribute with a suitable tool, e.g. rubber blade, and work into the substrate with an epoxy roller so that pores in the surface of the substrate are completely filled.
• It may be necessary to apply several layers.
• approx. 0.30 - 0.50 kg/m² binder (depending on the substrate)

Leveling layer / Roughness compensation

• The filled material (up to 1 : 1 parts by weight) is applied to the primed surface and distributed with a suitable trowel. If necessary, roll over with a spiked roller.
• Per mm thickness of base layer:
  approx. 0.85 kg/m² binder
  and 0.85 kg/m² Selectmix 01/03

Epoxy mortar

• The filled material (up to 1 : 10 parts by weight) is distributed with a smoothing trowel and smoothed.
• Per mm layer thickness: approx. 0.2 kg/m² binder
  and 2.0 kg/m² Selectmix 25

Base layer for blinding layer

• The filled material (up to 1 : 1 parts by weight) is applied to the primed surface and distributed with a suitable toothed trowel or toothed rubber blade. If necessary, roll over with a spiked roller.
• Then liberally broadcast fire-dried quartz sand over the base layer while it is still fresh.
• Remove any loose, excess material after hardening.
• Per mm thickness of base layer:
  approx. 0.85 kg/m² binder
  and 0.85 kg/m² Selectmix 01/03

‍